Mark & model : S8, The product is featured as large power rate laser tube, good stability and fast cutting speed,
which is suitable for the cutting of thin metal plate.
Origin : Asia and Pacific Area China
Quality standard : International
Submit date : 2012-11-28
H.S.Classification : Machinery & Electronics Electr.Element 8541 Semiconductor devices; light-emitting diodes etc.; parts thereof
Z8 Operation Instruction
1.Installation Requirement
Make sure to follow the operation instruction of model Z8 as shown in the illustration.
The dedicated power DY20 should be equipped. The positive pole of laser tube is in high voltage
(the ignition voltage is 30kv). It may cause the following consequence when it is failed to follow the
instruction: The cutting speed will be slowed because of the deformation of beam output model; Arcing;
the inner tube will be punctured by electricity and may cause water leakage.
2.Operation conditions
Water cooling: using purified water; 3 to 5 liter/minute; water temperature: 10℃-40℃. The operating
environment: temperature 2-40℃; humidity 10-60%.
The working current: test current is 32mA. Maximum working current is 32mA. The running
current must be kept below 30mA. The life span can reach 10,000 hours if the current is kept
below 28mA. The ammeter must be connected to the negative electrode of laser tube.
When it is working under overhigh current for long term, the negative pole will appear purple and the
life span will be shortened rapidly.To protect dust from going into the insulation sheath, please wrap
it with plastic film.
3.Working Performance
Cutting function.
Engraving function: Auxiliary Engraving. When the working current is 4mA and the tube is in
the state of preionization, the laser can be used for high-frequency impulse engraving.
4.Key Notes
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise
the output power will be seriously affected. The followings are the designated methods to
clean up pollution in the exterior surface of window mirror.
1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideways with an air blower.
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized.
5) If the methods above don´t work effectively, it is necessary to go after the professional workers to
use tampon with alcohol to clean the mirror surface from middle to edge. The best solution is to
prevent the window from being polluted.
Attention: it is forbidden to clean the mirror with acetone.
The screw in the front and back ends of the laser tube is not allowed to be moved, otherwise the out
power will be declined, even the laser will be scrapped.Put the acryl 300mm far away from output mirror,
when testing the laser spot.
5.Safety
The laser beam is invisible light. Please wear protective glasses when debugging the laser.
The positive pole is in high voltage. Pay attention to the security marks.
6.Storage and Transportation Requirement
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with
a dust-proof plastic bag. The storage environment is 2-40℃, and the requested humidity is 10-60%. Pack the laser as in the original way.
Important notes: it is requested to cement the sponge together with laser tube to prevent the
tube vertically sliding during transportation. The sponge in the side of output mirror must be 70 mm
beyond it, and the sponge in the side of reflecting mirror must be 50 mm wider.
7.Tubes operated in wrong way are not guaranteed by Manufacturer.
Cardboard Carton Package Size
DESCRIPBTION
|
N.W.
|
G.W.
|
PACKAGE/UNIT
|
C.W.
|
CBM
|
Laser Tube S2 (90W)
|
3.5KG
|
5KG
|
1360*250*260mm
|
18KG
|
0.088
|
Laser Tube S4 (100W)
|
4KG
|
7KG
|
1550*340*350mm
|
36.9KG
|
0.184
|
Laser Tube S6 (130W)
|
5KG
|
8KG
|
1800*340*350mm
|
43KG
|
0.214
|
Laser Tube S8 (150W)
|
6KG
|
11KG
|
2010*380*400mm
|
62.4KG
|
0.304
|
Laser Tube basic parameter
Model
|
Rated power
|
Max power
|
Length mm
|
Φmm
|
Catalyze
|
Life span ( h)
|
Warranty
|
S2
|
90W
|
100W
|
1200
|
80
|
Yes
|
10,000
|
10Months
|
S4
|
100W
|
130W
|
1400
|
80
|
Yes
|
10,000
|
10 Months
|
S6
|
130W
|
150W
|
1650
|
80
|
Yes
|
10,000
|
10 Months
|
S8
|
150W
|
180w
|
1850
|
90
|
Yes
|
10,000
|
10 Months
|
|